Electrical Defect Codes

01	Passed	46	Improper Boxes for Use
02	Failed	47	Boxes Not Cut In
03	Inaccessible	48	Support Boxes Properly
04	Job not Ready	49	Boxes Not Grounded
05	Too Many to List	50	Boxes Damaged
06	Defects Not Corrected	51	Sheath Not in Box or Connector
07	Need Qualified Individual to Call	52	General Use Receptacle Spacing
08	Service	53	Kitchen Counter Top Receptacle Spacing
09	Grounding	54	Recpt. Not Equally Divided on Small Appliance Circuit
10	Bonding	55	GFCI Defect General
11	Incorrect Size or Type Wire	56	GFCI Kitchen
12	Equipment Securely Mounted	57	GFCI Bathroom
13	Identify Conductors	58	No Recpt. Adjacent to Basin
14	Circuit Overloaded	59	No Continuity on Receptacle
15	Grouping of Mains	60	Device Loose in Box
16	Multiwire Circuits on Same Phase	61	Reverse Polarity on Recpt.
17	Loose Connections	62	Need Extension Rings
18	Isolate Neutral in Sub Pnl	63	Ground Switch
19	Label Panel	64	Devices not Installed
20	Panel Blanks	65	AFCI Defect
21	Need KO Stopper	66	Fixture not Installed
22	Covers Missing	67	Fixture Location
23	Troughs Overloaded	68	Recessed Fixtures not Wired
24	Secure Backfed Breakers	69	Recessed Fixtures in Contact with Combustible Material
25	Improper Overcurrent Prot	70	Support Light Fixtures
26	Inter Mixing Diff Class Circ	71	Closet Fixture Clearance
27	Clearances-Article 110-26	72	Fixture not Grounded
28	Separation Parallel Conduits	73	Install Smoke Detector(s)
29	Make Joints on Multi Wire Branch Circuit	74	Smoke Detector Location
30	Improper Wiring Method	75	Interlock Smoke Detectors
31	Cable Subject to Damage	76	Smoke Detector not Arc Fault
32	Support Cables	77	Install Blank Plate
33	Cables Damaged	78	No Disconnect on Equipment
34	Loose Joints	79	Equipment Not Wired
35	Free Conductor at Outlet Box	80	Need dedicated circuit to Equipment
36	Support Raceways	81	Line and Load Reversed
37	Need Stud Guards	82	Incorrect Wiring to Equip.
38	Cable Stapled too Close to Face of Stud	83	GDO Cord will not reach Receptacle
39	Raceways Overloaded	84	Cords
40	Terminate and Remove Unused Wire	85	Incorrect Wiring to Well
41	Improper Joints or Terminations	86	Incorrect Wiring to Sewer
42	Remove Temporary Wiring	87	Identify Disconnect
43	Circuit Shorted Out	88	Support of Pole
44	Ditches Not Deep Enough	89	Height of Pole
45	Boxes Overloaded	90	Ground Rod

W0	Wrong address on Permit	X5	No Permit for work being done
W1	Change of Contractor	X6	Job not Installed per Plans
W2	All Trades not Complete	X7	Permitted work occupied prior to CO
W3	Insp. Requested by other than Elect. Contr.	X8	Power turned on prior to Inspection
W4	Inspection Sticker Removed	X9	Need ladder on Job
W5	Insulated Prior to Inspection	Y1	Job not lockable
W6	Covered prior to Inspection	Y2	Framing added, wire not protected
W7	Ditches covered prior to Inspection	Y3	Equipment Damaged
W8	Defect caused by Others	Y4	Broken Boxes
W9	Improper use of Equipment	Y5	Wiring Damaged
X0	Approved Plan Error	Y6	Wiring Removed
X1	Display Permit	Y7	Whirlpool Access
X2	Display Address	Y8	Job exceeds Contractor's License
X3	Display Suite Number	Z1	Defect caused by Owner's Equipment
X4	No approved plans on Job	Z2	No 3rd Party Label